East Penn Carrier & Wrecker Sales Inc
7298 W Market St, Mercer PA 16137
Copyright @ 2011
East Penn Carrier & Wrecker Sales Inc
1100 Win Drive,Bethlehem PA, 18017
STANDARD FEATURES
96" Wide aluminum modular body
 Large forward compartments
Double panel doors
 Double action latches with keys
Toolbox lighting
 Mud flaps
Chain rack
 Attachment storage
Enclosed inner wheel wells
 Tailboard mounted D-rings
180" C.B
 Compartments over the wheel well
Door check
 Federal 108 lighting
Rubber fenderetes
 Side worklights
Fork holders
 Rubber isolators
Rigid torsional resistant mounting frame
 Two side pull grater blade attachments
Rotators have set the industry standard for superior
design and performance in heavy duty recovery
equipment for years. Based on that same past
knowledge and experience most rotators are equipped
with a hydraulic stabilization system that includes front
hydraulic outriggers with over 17" of spread and rear
patented outriggers designed for stability, in lifting as
well as anchoring your unit during those tough
recoveries.
Power elevation
 Power tilt
3-Stage design
 Safety chains in tailboard
70 degree pivoting crossbar
 8 pairs of cast steel forks
1 pair of hook adapters
 Power extension
Hydraulic fold
 2 Piece pivot pin
Low profile crossbar
 Low profile fork holder
upper/lower thrust washer
 1 pair of spring lift adapters
STANDARD UNDER LIFT SPECIFICATIONS
Additional lift attachments
 Front outrigger side pull attachment
Extension storage compartment
 Endless loop sling package
Snatch blocks
 Light bar
Halogen work & hook up lighting
 Wide load light bar
Rear camera & monitor
 Winch bucket mounted aluminum
Low pull "D" ring kit
 22" Rear outrigger extensions
Chain package
 Screw pini shackle kit
Snatch block storage rack
 Strobe kits
Xenon boom kits
 Low rider underlift
Engine data information center
 Power touch system - includes 8 functions
Tailboard cable tiebacks
 Wired and wireless controls
Air Shift PTO
 Radio proportional control with drivers
Side manual controls
 Convenience group
Navigation system
 3 or 7 drawer toolbox
Heavy duty tire lift
 25,000lb crossbar
Additional lighting
 2 Additional boom winches
Side mounted "D" rings
 House lock window (Drivers side)
STANDARD FEATURES
TRUCK SPECIFICATIONS
Boom maximum angle - 60 degrees
Boom maximum hook height - 445"
Reach past tailboard at minimum boom angle - 264"
Underlift winch capacity - (2) 60,000lbs (9975S)
Underlift winch type - Planetary 2 speed ( 9975S)
Cable - 7/8" x 250' (9975S)
Air winch tensioners - Standard (9975S)
Air winch clutch release - Standard (9975S)
Winch capacity - (2) 50,000lbs (9975S2)
Winch type - Planetary 2 speed (9975S2)
Cable - 3/4" x 200' (9975S2)
Air cable tensioners - Standard (9975S)
Air winch clutch release - Standard (9975S2)
Capacity fully extended to C.L of forks - 17,000lbs @ 143.5 (SDU-4)
Capacity fully retracted to C.L of forks - 55,000lbs @ 54" (SDU-4)
Underlift tilt - 10 degree (+) 10 degree (SDU-4)
Capacity full extended to C.L of forks - 18,000 @ 165 (Low Rider)
Capacity full retracted to C.L of forks - 55,000 @ 66" (Low Rider)
Underlift tilt - 10 degree (+) 7 degree
Front axle - 20,000lbs
Rear axle - 46,000lbs
Clear C.A or C.B - 180"
After frame from center of rear axle - 40"